SERVICE / 01
Connected Home
Maison connectée
Full smart-home systems for houses and apartments: design, hardware, wiring, lighting and climate automation, commissioning.
SARL · R.C.S. Caen · Trading since 2019
We wire buildings that think.
Normandie Home Connect designs, installs and commissions connected-home systems, commercial power and uninterrupted supply. One contractor from the first schematic to the signed handover file.
2019Registered in Caen
3Core service lines
24hReply to enquiries
100%Tested before handover
What we installThree service lines,
Three service lines,
one engineering standard.
Every project runs through the same chain — site audit, drawings, quoted bill of materials, installation, commissioning and a documented handover. Pick the line that matches your building.
SERVICE / 02
Commercial Electrical
Installation électrique
Power installations for offices, retail units and workshops: distribution boards, circuits, protection, testing and handover.
SERVICE / 03
UPS & Supervision
Onduleurs & supervision
Uninterrupted power and live monitoring for sites that cannot stop: UPS, sensors, automation network, alerting.
Indicative starting prices — a firm figure follows the site visit. VAT not applicable, art. 293 B of the French CGI.
Method
From first visit to signed handover.
No surprises halfway through the works. Each stage ends with something you can read, check and keep.
STAGE 01
Site audit
We walk the building, measure the existing supply, photograph the boards and note every constraint before quoting.
STAGE 02
Design & quote
Single-line diagram, zone plan and an itemised bill of materials. You approve the scope and the figure before we order.
STAGE 03
Installation
Cabling, boards, devices and network, installed to NF C 15-100 with the site kept usable wherever possible.
STAGE 04
Commissioning
Every circuit and every scene tested in front of you, then the as-built file, test report and a walkthrough.
Why this contractorBuilt to be handed over,
Built to be handed over,
not to be re-explained.
SINGLE POINT OF CONTACT
Design, supply and installation under one roof
Drawings, hardware procurement, wiring and configuration are handled by the same team, so nothing gets lost between an integrator and an electrician.
Standards first, aesthetics second — then both
Installations follow NF C 15-100 and manufacturer specifications. What you see is tidy; what you do not see is correct.
- Protection, earthing and selectivity calculated, not guessed
- Labelled circuits and a legible board schedule
- Test report handed over on completion
Open protocols
KNX, Zigbee, Modbus and standard IP. You keep the freedom to extend the system, or to have someone else do it.
Documented handover
As-built single-line diagram, device inventory, credentials and a short written guide — yours to keep.
STABLE
Supervision after the works
Where a site needs it, sensors and alerting keep reporting once we are gone.
Client projectsThree recent jobs,
Three recent jobs,
three signed invoices.
Each entry below corresponds to a completed and invoiced project. Client surnames and addresses are withheld for privacy.
They mapped the whole flat before touching a single cable. Lighting scenes, heating curves and the away mode all behave exactly as we agreed, and the handover file means I can actually change things myself.
SCOPE · Connected-home system — lighting automation and climate regulation
Marie F.
New distribution boards for a commercial unit, done between two trading weeks without losing a day. Every circuit was labelled, tested and signed off in front of me before they left the site.
SCOPE · Power installation — distribution boards and commissioning, commercial unit
Maria P.
We needed the site to survive a cut without anyone noticing. The UPS, the sensors and the alerting were configured together, so now I get a message before a problem becomes an outage.
SCOPE · UPS installation, monitoring sensors and automation-network configuration
Jeanna Z.
5.0average across the three projects
All works invoiced and completed on site
Registered contractor, R.C.S. Caen 851 801 779
CoverageNormandy first,
Normandy first,
the rest on request.
The workshop sits in Saint-Martin-de-Fontenay, ten minutes south of Caen. Calvados and the neighbouring departments are standard territory; projects further afield are quoted with travel included so the figure you see is the figure you pay.
SERVICE RADIUS
- Caen & Calvados — standard coverage, no travel surcharge
- Manche, Orne, Eure, Seine-Maritime — on request
- Ile-de-France & beyond — quoted per project
- Mon–Fri, 08:00–18:00 CET — site visits by appointment
2 Rue de la Paix · 14320 Saint-Martin-de-Fontenay
Free site visit in Calvados
Tell us what the building needs to do.
Send the address, a couple of photos of the existing installation and what you want out of it. You will get a written answer with an indicative range within one working day.